2009 RESULTS INDEX
& CHAMPIONSHIP
TABLE
Page 47
2009
FALCON PRO
HOME PAGE
Page 44
Home
RACE DATES AND VENUES FOR 2010
17th January       -    NORTH LONDON
March 7th            -    Pinewood Raceway  
May 16th              -    Oaklands Park
July 25th             -    Wellingborough
September 26th  -    Blackpool S C C
November 21st   -    Raceway 81
DARKSIDE RACING IS POWERED BY GODADDY WITH SOFTWARE FROM SERIF -
FIND OUT WHY AND GET SOME GREAT DEALS ON PRODUCT FOR YOU OR YOUR BUSINESS!
SERIES SPONSORS
Falcon Pro policy has been to stick to six rounds throughout the year, so as not to crowd the racing calendar and allow racers to have time in which to enjoy other forms of racing as well and this will continue in 2010.  

2010 will see 3 of the 6 rounds on 6 lane tracks and 3 rounds on 4 lane tracks.  Blackpool have now built their new 4 lane “Tangerine Dream” track we are sure this round will prove to be an interesting experience on a great new track!  See details here  http://www.blackpoolscc.info/tracks.html

Rules for 2010 are now published , the only changes being 2 new bodies allowed in 1/32 Falcon Sports and the Formula One body list has now been opened up to allow any mass manufactured bodies which fit chassis correctly.

Race format will stay the same.

We look forward to seeing you in 2010 for some more low budget, ultra close and fun racing!
The Falcon Pro Race Series is open to drivers of all levels. The 1/32 Sports class will be split into 2 different sub classes - Falcon & Falcon Pro. Racers may enter either Sub Class, but only one sub class per race.
General;-
1) ALL CLASSES ARE FOR SEALED / UNOPENED JK Falcon Motors Only. No other manufacturer motor allowed.
2) All bodies should be painted in prototypical or scale colour schemes, with a minimum of 2 race numbers - NO TWO TONE FADES OR CARRIER BAGS!
3) In all classes, the body must cover the guide flag.
Classes;-
Falcon Pro Formula One;-  Free Choice of chassis. Free choice of formula one bodies. Bodies must be commercially available, mass manufactured and cover the entire chassis with the exception of front wheel stub axles. Dimensional criteria as per BSCRA F1 class (except chassis dimensions in regard to the Devil and JK F1 chassis where the chassis dictates front axle detail.)

Falcon Sports 1/32
Any Le-Mans Car, open or closed cockpit raced from 1996 to the current day, manufactured by JK Products or Betta + MG Lola, Audi R8 and Peugeot 908 HPI from C.A.T.. with the exception of the following bodes -
JK American GTP, Betta Intrepid, Shadota & Silhouette Ferrari.
Chassis;- As per BSCRA 1/32 Novice Production rules (at November 22nd 2008) and also the JK Spring Steel Falcon chassis (1503/32 or 1503/42), built to BSL specifications (i.e. unmodified) and the JK Hypersport, 3 piece (unmodified).
Overall car width and body height to conform to BSCRA production rules.
Falcon Pro Sports 1/32
As above but free chassis choice.

Pro Falcon 1/24th Sports
Bodies - Any Le-Mans Car, open or closed cockpit raced from 1996 to the current day, manufactured by JK Products or Betta. No “Ultimate” bodies.
Maximum Wing height 38mm. Bodies should be cut to the cut line where available and have a minimum or 1mm vertical edge at the front of the body.
Chassis;- Any U.S.R.A. Approved, unmodified pressed steel production chassis (2 or 3 piece) from the following manufacturers - Parma, Champion, Slot Works, JK Products, Mossetti, Proslot.

Pin tubes must be in the original locations and may be floating or solid.  Pin tubes must be Straight and be located at 90 degrees to the centerline of the chassis. They may not be located or bent to minimise or modify chassis movement in any way. . No pin tube or attachment is allowed to any other part of  the chassis to either brace the pans or centre  section or  modify pan Movement

Front wheels;- Minimum 12.7mm diameter. 0.8mm wide. Wheels must be vertical, they may be entirely made of rubber or must have the outer portion of the tyre made from rubber.

Front Wheels / axle / stub axles must be located in the original axle holes.  There is no requirement for the front wheels to be mounted on a one piece front axle, wheels may be mounted on pins if desired, but must locate through the original axle holes. Wheels must be located on the outer face of the front wheel pillar blocks/mountings within 6mm of outer edge of chassis.

A small amount of material may be removed from the inside of the motor bracket to correctly locate motor but the outer profile of the motor bracket (if intrinsic in the design) must remain unaltered.

Motor & or rear pillar block bracing is allowed. However all must be located BEHIND the centre line of the motor shaft and strictly within the confines of the chassis.
The Minimum rear axle height (when measured from the underside of the chassis to the top surface of the rear axle) is 8.5mm.
Soldering or gluing of additional fittings of any kind may not be attached in any way to the standard chassis to facilitate Lead wire attachment. However a piece of lexan or tape across the opening in the centre section to prevent lead wires dropping is acceptable providing it does not modify chassis movement.
Lead may be attached to the top of the chassis to adjust balance and weight distribution but in no way must this adjust or be seen to modify chassis movement.

The scrutineers decision on all above matters is final.

ACCOMMODATION

PLEASE NOTE,  AS OF NOVEMBER, TRAVEL LODGE HAVE A SALE AT PRESENT AND YOU COULD BOOK  2010 VENUES FOR A HUGE REDUCTION IF YOU ACT FAST!

http://www.travelodge.co.uk

http://www.premierinn.com

http://www.innkeeperslodge.com

http://www.4hotels.co.uk/uk/hotels/admiralc.html

http://www.bedandbreakfasts.co.uk

http://www.venuemasters.co.uk   
Falcon Pro 2010 Rules
RESULTS PUBLISHED
Page 57
RESULTS PUBLISHED
Page 58
2010 CHAMPIONSHIP TABLE
Page 59
RESULTS PUBLISHED
Page 60
RESULTS PUBLISHED
Page 61
RESULTS PUBLISHED
Page 62
SEE DETAILS FOR THE 2011 FALCON PRO SERIES !!
Page 64
CLICK HERE FOR FINAL RESULTS
Page 64